Anyone who collects badges for a while sooner or later needs to describe a badge precisely and briefly – so that two collectors understand each other without a photo or long explanations. That is what the six-digit badge code is for, a common reference system used by Czech and Slovak collectors. This article sums it up in clear tables.
Why code badges
The same badge design often exists in several issues – enamelled or just painted, in yellow or white metal, with a pin or a screw. Without a precise description a collector can easily buy the same badge twice, or miss a rarer variant. The badge code captures these differences in three pairs of digits and is also handy for keeping a collection on a computer: in a spreadsheet you can easily find, for example, all enamelled badges in white metal.
How the code is built
The code has six digits in three pairs, usually separated by full stops:
| Position | What it defines | Example |
|---|---|---|
| 1st pair | material the badge is made of | 01.03.10 – struck yellow metal |
| 2nd pair | surface finish | 01.03.10 – painted, coated with resin |
| 3rd pair | type of fastening | 01.03.10 – pin (butterfly clutch + shank) |
A few more examples: the same badge in white metal has the code 11.03.10, and with a soldered pin bent at 90° 11.03.01. An enamelled yellow-metal badge with a pin soldered perpendicular and bent at 90° has the code 01.01.01; with a pin soldered horizontally and bent back by 180° it is 01.01.02.
Table 1: Material (first pair)
| Code | Material |
|---|---|
| 01 | struck yellow metal |
| 02 | cast yellow metal – sprayed |
| 03 | yellow metal cast in a mould |
| 04 | domed yellow metal |
| 05 | domed yellow metal with damascening on the reverse |
| 06 | yellow metal with damascening on the reverse |
| 07 | yellow metal with damascening on the reverse and a 3D figure (e.g. ball, kangaroo) |
| 08 | yellow metal with a 3D figure |
| 09 | domed yellow metal with a 3D figure |
| 11 | struck white metal |
| 12 | cast white metal – sprayed |
| 13 | white metal cast in a mould |
| 14 | domed white metal |
| 15 | domed white metal with damascening on the reverse |
| 16 | white metal with damascening on the reverse |
| 17 | white metal with damascening on the reverse and a 3D figure |
| 18 | white metal with a 3D figure |
| 19 | domed white metal with a 3D figure |
| 21 | flat yellow sheet metal |
| 22 | flat white sheet metal |
| 23 | flat anodised sheet metal |
| 24 | domed anodised sheet metal |
| 25 | aluminium sheet |
| 26 | “silver” aluminium sheet with damascening on the reverse |
| 27 | “gold” aluminium sheet with damascening on the reverse |
| 28 | sheet metal with a pressed relief of image or lettering visible from the reverse |
| 31 | badge made of two metals |
| 34 | glass |
| 35 | porcelain |
| 36 | plastic |
| 37 | yellow metal with a set stone |
| 38 | white metal with a set stone |
| 39 | silver |
| 40 | gold |
Unused numbers (10, 20, 29, 30, 32, 33) are reserved in the system for further materials.
Table 2: Surface finish (second pair)
| Code | Surface finish |
|---|---|
| 01 | enamel |
| 02 | paint |
| 03 | painted, coated with resin |
| 04 | bare metal without colour |
| 05 | offset print coated with resin |
| 06 | offset print on anodised sheet metal |
| 07 | sprayed |
| 13 | print on plastic |
| 14 | printed sticker |
| 15 | metal worked in relief (mainly old sheet-metal badges) |
Table 3: Fastening (third pair)
| Code | Type of fastening |
|---|---|
| 01 | pin soldered perpendicular to the badge face, bent at 90° |
| 02 | pin soldered horizontally to the face, bent back by 180° |
| 03 | pin spot-welded perpendicular to the face, bent at 90° |
| 04 | pin spot-welded horizontally to the face |
| 05 | pin spot-welded horizontally to the face in a recess |
| 06 | pressed-in pin |
| 07 | glued pin |
| 08 | stud |
| 10 | pin (butterfly clutch + shank) |
| 11 | screw with nut |
| 13 | simple brooch clasp (non-sprung lever) |
| 14 | sprung brooch clasp (coiled spring) |
| 15 | hinged brooch clasp |
| 16 | brooch clasp with a segment catch |
| 18 | pin set in plastic |
Damascening on the reverse
Damascening is a fine ornament on the reverse of a badge. The term comes from heraldry, where coloured areas without figures were decorated in this way. For collectors it matters because it helps to tell apart issues of badges with the same front design – and sometimes an original from a copy. That is why damascening has its own material codes: for yellow metal it changes the code from 01 to 05 or 06, for white metal from 11 to 15 or 16. When coding a badge, always turn it over and check the reverse first.
The source reference gives an example with the badge of the club 1. FC Synot Staré Město:
| Dimensions (mm) | Reverse | Code | |
|---|---|---|---|
| Original | 21.1 × 25.7 | damascening, maker's mark Kovoznak Vlčnov | 16.03.03 |
| Copy (fake) | 22 × 26 | plain reverse without damascening | 11.03.03 |
Badges that look identical at first glance are thus told apart only by the reverse and precise measurement.
How to measure a badge correctly
Dimensions are given as base × height in millimetres – width first, then height. A figure of 14.2 × 18.1 mm therefore means a badge 14.2 mm wide and 18.1 mm high. Only the badge itself is measured, without the pin or other fastening.
A vernier calliper is used for measuring. Whole millimetres are read on the main scale, tenths on the sliding vernier – where a vernier line exactly matches a line on the main scale. Badges are not made with absolute precision, so a tolerance of ±0.1 mm is normal. Do not measure with the very tips of the jaws, which tend to be inaccurate on cheaper callipers, but as close to their base as possible.
How we use the codes at FANzone
For the badges we offer, we state the material, surface finish and fastening according to this system. For example, the Olympic badge, Tokyo 1964 is made of yellow metal (01), painted (02) and has a pin soldered perpendicular and bent at 90° (01) – so its code is 01.02.01. Browse our full range of sports badges and read also how to recognise an original sports badge.
Frequently asked questions
What does the badge code 01.01.01 mean?
It is a badge struck from yellow metal (01), enamelled (01) and with a pin soldered perpendicular to the face and bent at 90° (01). The first pair of the code defines the material, the second the surface finish and the third the fastening.
How are badge dimensions stated?
As base × height in millimetres, i.e. width first and then height. The badge itself, without the pin, is measured with a vernier calliper, with a usual tolerance of ±0.1 mm.
Why does damascening on the reverse matter?
Damascening helps to tell apart issues of badges with the same front and sometimes an original from a copy. That is why it changes the material code in the system, for example from 01 to 05 or 06 for yellow metal.
Sources
- Rudolf Kirchner: Badge codes (Kódy odznaků) – reference system for coding badges, damascening and measuring with a vernier calliper, odznaky.wz.cz